Shoreline Offroad Pro Series 8pc Pure White Rock light Kit

What's in the Box

• Eight pure white rock light pods
• LEDShow double zone Bluetooth controller
• Controller power harness with inline fuse
• RF remote

Tools You Will Need

• Drill and bits or a screwdriver for pod mounting
• Zip ties and electrical tape
• A 12V source for the bench test

Read This First

• Disconnect the battery before any wiring.
• If your rig runs an auxiliary switch panel, disconnect the panel at the switched fuse so every circuit stays dead while you work.
• Plan the whole install before the first hole: pod placement, lead runs, and controller location from the next two cards.
• The controller is the brain of this kit. Everything runs through the LEDShow app or the RF remote.

Where the Pods Go

Eight pods is enough to ring the whole underside: wheel wells, frame rails, rock sliders, and bumpers are the usual homes. Point the pods down and slightly out, so the light pools on the ground around the rig and shows you the terrain and your tire placement.

• Keep pods and leads clear of steering and suspension travel, and away from exhaust heat.
• Dry-fit every pod and lead before you drill or stick anything down.
• Route leads along the frame toward the controller, and keep plugs where you can reach them later.

The controller runs two zones. Group your pods by area, front half and rear half, so each half can run its own brightness and mode.

1. Bench test first. Connect the controller to a 12V source on the bench, plug in a pod, and confirm the app pairs and the pod answers before anything goes on the rig.
2. Mount the controller in a dry spot, under the hood or in the cab, where its leads reach your pod runs.
3. Mount the pods from the placement card, and run each pod's lead back to the controller, plugged into the zone outputs in the groups you planned.
4. Wire power. Red to a fused 12V source. Shoreline recommends a switched ACC or fuse box circuit, so the controller sleeps with the rig. Black to a clean ground: bare metal on the chassis, the battery negative, or an engine ground.
5. Reconnect the battery, power the kit on, and pair the app from the next card.
6. Test every pod and every zone, then zip tie the leads up and out of harm's way.

Wiring Note: Shoreline's standard install uses the red and black power wires only. Your harness also carries blue and white override wires. We do not recommend wiring them, but they are there if you want the option. The white wire is this controller's documented override: it brings both zones on solid white from a switch or a courtesy circuit, even when the kit is off at the app or remote. Because an override can light the kit while the controller shows off, most owners who use one put it on its own switch.

The LEDShow app runs this kit from your phone, and the included RF remote covers the same basics when your phone is not handy. The controller runs two independent zones, so the front and rear of your rig, or the left and right, can sit at different brightness and modes.

Pairing the App

1. Download LEDShow from the App Store or Google Play. A QR code for it is in the box.
2. Finish the wiring and power the kit on.
3. Open LEDShow. It finds the controller and connects over Bluetooth on its own. Do not pair from your phone's Bluetooth settings menu. If you already did, delete the app and reinstall it, then open it again.
4. A connected app shows a device named HYLEDTEST in the device menu at the top left. That is your controller.
5. The two zones sit at the top of the main screen. Tap a zone to set it, and tap it again to release it. The Bluetooth device icon can run more than one controller at once.

What the App Does

• Six modes: Static, Blink, Breathing, Strobe, Wigwag I (the light jumps from the first zone to the second), and Wigwag II (a strobe jumps zone to zone).
• Brightness runs 0 to 100, and the effect speed adjusts per zone.
• On the RF remote, the mode buttons call up Blink, Breathing, Strobe, Static, Wigwag I, and Wigwag II directly, and the I and II keys switch the zones.
• Settings, top right: timing and more.
• Power cut memory: the controller keeps your last setting when power cycles.

Pairing the RF remote: pull the fuse to cut power. Hold the remote's power button down and put the fuse back in, holding for two more seconds. The fob lights blink when the pairing lands.

Specs

• Output: 9,100 lumens
• Power: 20W per pod
• LEDs: 219 per pod
• Sealing: IP68 waterproof
• Voltage: DC 12V
• Zones: 2 independent zones
• App: LEDShow (Bluetooth) with RF remote
• Warranty: 2 years

• No device shows in the app: give LEDShow location, Bluetooth, and file access in your phone's app permissions, restart the phone, then reopen the app.
• The app will not connect, but the remote works: delete the app, pull the fuse for five minutes, reinstall the app, and power back up.
• The app works, but the remote does not: put fresh batteries in the remote, then re-pair it with the fuse procedure in the app card.
• The controller drains the battery: power the controller from the vehicle's ACC or fuse box, or another switched circuit, not straight off the battery.
• One pod stays dark: check its plug and lead first, then confirm its zone is switched on.